Eldes EKB3 Manuel d'installation Page 157
- Page / 168
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
157
157EN
MANUAL ELDES ESIM264 V3.1
+
+ -
-
- +
- +
MOUNTING POINT AMOUNTING POINT B
MOUNTING POINT A
Ensure to screw in properly for supervision of the back side by tamper switch
MOUNTING
POINT B
110 111
3. Remove the plastic tab inserted between one of the battery terminals and battery slot contacts.
The wireless connection loss between EWS3 and ELDES alarm system leads to alarm. The system identies this event as a tamper viola-
tion and sends an alarm by SMS text message and phone call to the user (-s) by default. The SMS
message contains the wireless device model, wireless ID code and tamper number.
112
4. STATUS indicator should start ashing indicating successful data transmission.
5. Close EWS3 enclosure by putting the cover back.
6. Bind the device to the alarm system by sending a corresponding command via SMS text message or using ELDES Conguration Tool
software. Please, refer to the software‘s HELP section or refer to 19.1. Binding, Removing and Replacing Wireless Devices for
more details.
7. The system automatically informs about successful/unsuccessful binding process. If attempt to bind is unsuccessful, try to move
EWS3 closer to alarm system device and bind it again.
ATTENTION: Ensure that EWS3 device is properly xed to the wall and the Mounting Point A portrayed in Fig. No. 110 and Fig. No. 111
is properly screwed in. Otherwise, the tamper switch will NOT supervise the back side of EWS3 enclosure (see also 33.12.3. EWS3
Zone, PGM Output and Tamper).
NOTE: If you are unable to bind the wireless device, please, restore the parameters of the wireless device to default and try again.
See chapter 33.12.5. Restoring Default Parameters for more details.
32.12.3. EWS3 Zone, PGM Output and Tamper
Upon successful EWS3 outdoor siren binding process,the system adds 1 wireless Instant zone and 1 wireless Siren PGM output. The
wireless zone is intended for EWS3 tamper control and ability to assign a partition (-s), while the wireless PGM output is intended for siren
speaker control.
In case of tamper violation, the alarm is caused regardless of system being armed or disarmed. There are 2 ways to detect tamper viola-
tion on EWS3:
• By tamper switch. EWS3 comes equipped with 2 built-in tamper switches intended for enclosure supervision:
• one located on the front side of the PCB supervising the front cover in case it is illegally opened (see Fig. No. 107).
• the other one located on back of the PCB supervising the back side of the enclosure in case the EWS3 is illegally detached from the
wall (see Fig. No. 107).
Once the enclosure of EWS3 is tampered, the tamper switch will become triggered. This action will be followed by alarm, resulting in
sending an SMS text message and/or phone call to the user. The SMS text message contains the violated tamper number.
• By wireless connection loss. The wireless connection loss between EWS3 and ESIM264 system leads to alarm. The system identies
this event as a tamper violation and sends alarm by SMS text message and phone call to the user (-s) by default. The SMS text message
contains the violated tamper number and a star * character indicating wireless connection loss as a tamper alarm cause.
ATTENTION: The tamper will not operate if the wireless zone is disabled.
- INSTALLATION MANUAL 1
- Installation Manual v3.1 2
- Contents 3
- Limited Liability 5
- Manufacturer Warranty 5
- Package Content 5
- About Installation Manual 5
- 1. GENERAL INFORMATION 6
- Ping Period 10
- MANUAL ELDES ESIM264 V3.1 11
- 2. TECHNICAL SPECIFICATIONS 12
- GSM signal strength 13
- SIREN/BELL 14
- Parallel Wiring Method 19
- 3. INSTALLATION 20
- 0.5 m to 30 m 23
- 0.5 m to 150 m 23
- 5. CONFIGURATION METHODS 25
- 6. PASSWORDS 28
- 7. SYSTEM LANGUAGE 29
- 8. USER PHONE NUMBERS 30
- 9. DATE AND TIME 33
- 10. USER PASSWORDS 34
- 11. iBUTTON KEYS 36
- 12. ARMING AND DISARMING 38
- 13. EXIT AND ENTRY DELAY 46
- 14. ZONES 48
- 15. STAY MODE 56
- 16. TAMPERS 57
- 19. WIRELESS DEVICES 67
- 20. SIREN/BELL 71
- 23. PARTITIONS 78
- 24. TEMPERATURE SENSORS 81
- 27. SYSTEM NOTIFICATIONS 86
- 28. EVENT LOG 90
- 30. MONITORING STATION 93
- 31. ELDES WIRED DEVICES 108
- 00:4520,2 109
- Jumper position Address 117
- AUX- AUX+ 118
- D1 D2 D3 D4 D5 D6 D7 D8 122
- AU X- AUX+ 123
- 32. ELDES WIRELESS DEVICES 126
- Power supply 128
- MAX 20 mm 131
- 0-90% RH @ 0... +40 °C 135
- (non-condensing) 135
- RESETLED 136
- C1 C2 Z1 Z2 COM 141
- Battery Voltage 143
- ANYWHERE 144
- IN THIS AREA 144
- Mounting slot 146
- Battery pocket door 146
- Mounting plate 146
- FRONT SIDE 151
- BACK SIDE 151
- Press and hold 152
- Insert a screwdriver or 152
- 20 mm max 153
- FRONT SIDE of ENCLOSURE 156
- MOUNTING POINT A 157
- MOUNTING 157
- 33. REMOTE SYSTEM RESTART 159
- 34. TECHNICAL SUPPORT 160
- 35. RELATED PRODUCTS 164
- DS1990A-F5 - iButton key 165
- 166
- EWS3 - wireless indoor siren 167
- Made in the European Union 168
Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Eldes EKB3
(26 pages)
(16 pages)
(44 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.065 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels