Eldes ESIM364 Manuel d'installation télécharger pdf (Page 47)

47EN

MANUAL ELDES ESIM364 V1.0

14. ZONES

Detection devices such as motion detectors and door contacts are connected to the alarm system’s zone terminals. Once connected, the

associated zone’s parameters must be congured.

ESIM364 comes equipped with 6 on-board zones allowing to connect up to 6 detection devices. For more details regarding zone expansion,

please refer to 14.2. Zone Expansion.

ESIM364 zones are classied by 5 categories:

Zone category Description

Max. number of

zones per device

Max. number of

zones in total

On-board Zones Built-in wired zones of ESIM364 alarm system. 6/12* 6/12*

Keypad zones Hardwired zones of EKB2/EKB3 keypad. 1 4

EPGM1 zones Zones of EPGM1 - hardwired zone & PGM output expansion

module.

16 32

Wireless zones Non-physical zones automatically created by connected

wireless devices.

2** 64***

Virtual zones

Non-physical zones intended for Panic button feature (alarm

activaiton upon pressing the button) on EWK1 wire less key-

fob. Virtual zones can be manually created using ELDES Con-

guration Tool software.

64**** 64****

* - 6-Zone mode is enabled by default. ATZ mode doubles the on-board zone number and increases it to 12 in total.

** - Depends on the connected wireless device.

*** - Available only if no zones, EPGM1 zones and virtual zones are present.

**** - Available only if no zones, EPGM1 zones and wireless zones are present.

14.1. Zone Numbering

The zone numbers ranging from Z1 through Z12 are permanently reserved for on-board zones even when ATZ mode is disabled. The

Z13-Z76 zone numbers are automatically assigned in the chronological order to the created virtual zones and the devices connected to the

system: keypads, wireless devices, EPGM1 modules.

14.2. Zone Expansion

For additional detection device connection, the number of zones can be expanded by:

• enabling the ATZ (Advanced Technology zone) mode (see 14.4. ATZ (Advanced Technology Zone) Mode).

• connecting EPGM1 hardwired zone and PGM output expansion module (see 32.1.3. EPGM1 – Hardwired Zone & PGM Output Ex-

pansion Module).

• connecting keypads (see 32.1.1. EKB2 – LCD Keypad, 32.1.2. EKB3 – LED Keypad and 33.1. EKB3W – Wireless LED Keypad).

• binding wireless devices (see 19. WIRELESS DEVICES).

• creating virtual zones (see ELDES Conguration Tool software’s Help section).

The maximum supported number of zones is 76.

14.3. 6-Zone Mode

By default, ESIM364 alarm system runs in the 6-Zone mode under zone connection Type 1 allowing to connect up to 6 detection devices

of NO (normally-open) type to the on-board zone terminals as indicated in the wiring diagram of Type 1. Once a dierent zone connection

type is set, the detection device wiring must be done according to the wiring diagram of the associated type. Available zone connection

types for the 6-Zone mode:

• Type 1 – Parallel wiring of NO (normally-open) detection device with 5,6k EOL (end-of-line) resistor.

• Type 2 – Serial wiring of NC (normally-closed) detection device with 5,6k EOL resistor.

• Type 3 – Combination of serial and parallel wiring of tamper with 5,6k EOL resistor and NC (normally-closed) detection device with

3,3k EOL resistor.

For zone wiring diagrams of the 6-Zone mode, please refer to 2.3.2. Zone Connection Types.

Set zone connection

type for 6-Zone mode

EKB2

Menu path:

OK → CONFIGURATION → OK → aaaa → OK → ZONES → OK → ZONE TYPE:6-ZONE M

→ OK → TYPE 1... 3 → OK

Value: aaaa – 4-digit administrator password.

1 2 ... 42 43 44 45 46 47 48 49 50 51 52 ... 165 166

Commentaires sur ces manuels

Pas de commentaire

Eldes ESIM364 Manuel d'installation Page 47

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Eldes ESIM364